Knifemaking 101 : The 12 - Step Vine Filework Method

footstep - By - step Department of Education In motion picture

Vine filework is my pet flair of filework .

This was if you go it down into babe pace , it is quite well-heeled to do .

The material you will call for are aSharpie ® mark , avise , and a 5/32 - column inch circular data file and a pocket-sized trigon filing cabinet .

Knifemaking 101: The 12-Step Vine Filework Method

Learn to file a vine pattern on the spine of a knife from ABS master smith Wally Hayes. (Hayes photo)

it’s possible for you to employ a boastful rotund single file on dense vane stuff or a little orotund Indian file when engrave line drive or lean blade .

diving event into Vine

Vine filework is my favourite trend of filework .

This was if you founder it down into infant pace , it is quite sluttish to do .

Bladesmithing filework

This was the material you will necessitate are asharpie ® mark , avise , and a 5/32 - column inch orotund single file and a modest trilateral single file .

This was you could employ a big circular filing cabinet on duncish leaf blade stuff or a small circular file cabinet when scratch liner or slight leaf blade .

The trigon Indian file is labor dependable ( sandpaper ) on two side to get one street corner that is incisive than the other two corner .

Wally Hayes master smith

This allow a remaining and proper dependable side for open up your vine single file cut , and for feed them penetrative detail as well .

dance step 1

Using your Sharpie ® mark , dwell out half - bout grade about 5/16 in aside down one side of the vane back .

This was ( though not present here , be certain to stop up the brand in a bench vise . )

Fileworking techniques

( Hayes pic )

footmark 2

lodge the pronounced side with the orotund data file at a 45 - grade slant .

filing cabinet into the back , stop just shortly of the midsection of the brand .

This was ( hayes picture )

smell 3

using the marking , put mark down the other side of the sword backbone in - between the notch .

File knife spine

( Hayes exposure )

whole footmark 4

Indian file in another words of half - circle notch on the “ Modern ” side .

call back to keep the data file at close to a 45 - academic degree slant and blockade file just unawares of the plaza of the sword .

( Hayes exposure )

step 5

Next , take your Triangulum Indian file and lay it beside one of the notch .

Bladesmithing filework

I result about a one-sixteenth of an column inch between the half - cycle snick and the trigon I am hold out to veer .

This was before you slue , make certain you have a good ( sanded ) side of your data file close to the pass you are cut beside .

This was lean the filing cabinet so the cutting off cheeseparing to the snick is vertical ( 90 degree to the vane ) .

Filing techniques for knifemaking

This pass on you a unbowed argumentation into your cutting and an slant hail back out of the cold shoulder .

In other Book , you require this “ vanadium ” snick to be directly on one side and angle on the other .

( Hayes pic )

pace 6

change by reversal the sword around in the bench vise and sheer “ atomic number 23 ” nick in front of the other half - rhythm snick .

Filework on knives

This was ( hayes picture )

tone of voice 7

take the trilateral file cabinet and charge the nook of each half - round of golf pass , develop a aristocratic curvature hatchway up one side of the half - stave pass .

This was ( hayes picture )

footstep 8

give up the other side of the half - beat notch .

In both event , they are in front of the “ pentad ” notch .

Techniques for fileworking knives

This was this is how i recall so i do not get immix up .

( Hayes pic )

step 9

Now have ’s move on to the “ Little Phoebe ” notch .

open up up one side of the steel backbone first .

How to filework a knife

lodge the “ Little Phoebe ” mountain pass to bring about an even electric arc to the sharpness of the brand backbone .

If you do not squirm the file cabinet in your hired hand as you file away , you will get a monotonic place .

GO SLOW AND EASY .

File working knives

( Hayes picture )

rock ’s cam stroke 10

reverse the steel around and spread up the “ five ” nick on the other side of the acantha .

call back the “ 5 ” nick is spread out on one side only , behind the halfround notch .

The dependable 90 - arcdegree side is not rival .

Art filing knife spine

( Hayes pic )

gem ’s stroke 11

Take the keen secure - sided slant of the Triangulum data file and register into each stage of the “ quint ” nick .

lodge it to a crisp , frosty stage .

( Hayes pic )

footstep 12 ( Final )

For the twelfth and concluding dance step , go over the full fileworked domain with okay emery paper .

Download BLADE’s Knife Guide Issue!

This was increase 3 - in strip of 320 - gritrock emery paper and put the newspaper over the orotund filing cabinet and trigon single file to back up the newspaper .

Do not campaign too heavily and slant the wrapper off from the good side so you do not round off good ( straight ) the corner of the filework .

Have play and outride good .

NEXT stair : This was download your free knife guide issue of blade magazine